How to Prime a Well Pump (Shallow and Deep Well Jet Pumps)
Boreholeflow is reader supported. When you buy through links on this page, I may earn a commission at no extra cost to you. Read the full disclosure.
- Only above ground jet pumps need priming. Submersible pumps sit under water in the well and never need it.
- To prime, turn off the power, remove the priming plug, fill the pump with water until it overflows, replace the plug and restart.
- Shut the pump off if it runs for more than a couple of minutes without building pressure. Running dry ruins the shaft seal.
- A pump that keeps losing prime has a leak, usually a worn foot valve or a suction pipe joint that lets in air.
A jet pump that hums but pumps no water, or a pressure gauge stuck near zero after a power cut, usually means the pump has lost its prime. The good news is that priming usually needs only a bucket of water, a wrench and half an hour.
This guide shows how to tell if your pump needs priming, the steps for shallow and deep well jet pumps, and how to fix a pump that keeps losing prime.
Does my pump need priming? Quick check
Does my pump need priming? Quick check
Answer three questions about your setup. We tell you what kind of pump you probably have and what to do next.
Why jet pumps lose their prime
A jet pump sits above the water and pulls it up by suction. It can only do that when the pump body and the suction pipe are full of water with no air.
A foot valve at the bottom of the suction pipe, or a check valve near the pump, keeps that water from draining back into the well. When air gets in or water drains out, the pump spins but moves nothing.
- A power outage, if the valve leaks and the water drains back while the pump is off.
- Work on the plumbing that opened the suction side.
- The water level dropping below the end of the suction pipe in a dry spell.
- An air leak at a fitting, a cracked pipe or a worn foot valve.
Shallow well jet pumps are practical when the total lift is under about 18 feet (5.5 metres), according to Alberta Agriculture’s guide to shallow well jet pumps. Water deeper than that needs a deep well jet or a submersible pump.
What you need
- A bucket or two of clean water, or a garden hose from another supply.
- An adjustable wrench or the right size socket for the priming plug.
- Thread seal tape for the plug.
- A funnel helps on pumps with a small priming port.
See priming supplies on Amazon
How to prime a shallow well jet pump
- Turn off the power to the pump at the breaker. A pump running without water damages its seal.
- Release the pressure. Open a tap near the pressure tank until the gauge reads zero, so water does not spray when you open the plug.
- Close the valve to the house if you have one, so the water you add stays in the pump.
- Remove the priming plug on top of the pump. Some pumps also have an air relief plug; remove it too.
- Pour water in slowly until it fills the pump body and comes out of the priming hole. This can take a few gallons if the suction pipe drained.
- Watch the level for a minute. If it keeps dropping, water is leaking back into the well through the foot valve or pipe.
- Replace the plug with fresh thread seal tape and tighten it.
- Turn the power back on. The pump should build pressure within a minute or two.
- Bleed the air by opening the taps one at a time until the water runs steady.
If the pressure gauge climbs to the cut out setting and the pump stops, it is primed. These steps follow the procedures summarised by InspectAPedia from Goulds and Zoeller manuals.
Some pumps need two or three rounds, especially with a long suction pipe. Loosening the priming plug slightly while the pump runs lets trapped air escape; tighten it as soon as water flows steadily.
Priming a deep well (two pipe) jet pump
Deep well jet pumps have two pipes going into the well: a suction pipe and a pressure pipe that drives the jet. They are primed the same way, but hold more water.
- Fill through the priming port until water overflows. On some models, a vent plug above the suction pipe lets air out while you fill.
- Check the pressure control valve setting in the manual before you restart. Deep well jets need the right back pressure to work.
- Expect to repeat the fill once or twice before the pump holds pressure.
Convertible jet pumps can be set up for shallow or deep wells. Check your manual to see which setup you have before you prime.
If priming does not work
- The pump runs but pressure never builds. Air is still in the system or the suction side leaks. Turn it off and prime again.
- The water level drops after you fill it. The foot valve or check valve is not holding, or a pipe is cracked.
- The water is cloudy with tiny bubbles. Air is getting in through a suction fitting. See air in well water lines.
- The pump hums but does not spin. This is an electrical or motor problem, not a prime problem. See well pump not working.
- The water level in the well is too low. In a drought the suction pipe can end above the water. See signs your well is running dry.
Why a well pump keeps losing prime
One lost prime after an outage is normal. Losing it every few days means something is letting water out or air in.
| Cause | How to tell | Fix |
|---|---|---|
| Worn or stuck foot valve | The pump loses prime overnight with all taps closed | Pull the suction pipe and replace the foot valve |
| Leaking check valve at the pump | Water drains back as soon as the pump stops | Inspect and replace the check valve |
| Air leak at a suction fitting | Bubbles in the water or in a clear filter housing | Reseal or tighten the joint, replace cracked fittings |
| Cracked suction pipe | Water level drops after you fill the pipe from the top | Find and replace the damaged section |
| Leak on the house side | The pump cycles with every tap closed | Find the running toilet, leaking fitting or tank valve |
Causes and checks summarised from InspectAPedia’s guide to repeated loss of prime.
Replacing a foot valve means lifting the suction pipe out of the well. Many owners do this on shallow wells; if the pipe is long or the well is deep, a pump service is worth the call.
How to stop it happening again
- Replace a tired foot valve before it fails completely.
- Add dry run protection. A pump protector shuts the motor off when there is no water. See well pump protection devices.
- Keep the pump from freezing. Ice cracks pump bodies and pipes. See how to keep a well pump from freezing.
- Plan for outages. A generator or battery backup keeps the pump running. See battery backup for a well pump and well water without power.
- Consider an upgrade. If the water level is near the pump’s limit, a submersible pump never needs priming.
Shopping for a new pump? Compare the best shallow well jet pumps and check what size well pump you need.
Lost prime after a freeze? Ice in the suction line can crack fittings and let air in. Check our frozen well pipes guide before you prime again, and see heat tape options to stop it happening next time.
Frequently asked questions
How long does it take to prime a well pump?
Often under half an hour. A long suction pipe or a leaking foot valve can mean two or three rounds of filling.
Do submersible well pumps need to be primed?
No. Submersible pumps sit under the water in the well, so they are always full of water. Only above ground jet pumps need priming.
Why does my well pump lose prime after a power outage?
The foot valve or check valve is letting water drain back into the well while the pump is off. A valve in good condition holds the water.
Can I prime a well pump with a garden hose?
Yes, if you have water from another source, such as a neighbor or a storage tank. Feed it into the priming port until the pump is full.
How long can a jet pump run without water?
Only a minute or two. Running dry overheats and damages the shaft seal, so turn the pump off if it does not build pressure quickly.
What is a foot valve?
A one way valve with a strainer at the bottom of the suction pipe. It lets water in and stops it draining back, so the pump stays primed.






