8 Signs Your Well Is Running Dry (and What to Do Next)
Boreholeflow is reader supported. When you buy through links on this page, I may earn a commission at no extra cost to you. Read the full disclosure.
- The classic sign of a well running dry is water that sputters or stops during heavy use, then returns after the well rests for an hour or more.
- Air in the taps, muddy or sandy water and a pump that runs longer than usual are the other early warnings.
- Many “dry well” calls turn out to be a pump, pressure switch or pressure tank problem, so rule those out first.
- Use the symptom checker below to see which is more likely, then follow the steps for your result.
Few things are as worrying for a well owner as turning on the tap and getting a splutter of air. Is the well drying up, or is something else wrong?
This guide covers the signs your well is running dry, how to confirm it, what to do in the next 24 hours, and the long term fixes, from storage tanks to deepening the well.
Is my well running dry? Symptom checker
Is my well running dry? Symptom checker
Tick everything you have noticed. The checker weighs the signs that point to low water in the well against those that point to a pump, switch or pressure tank problem.
8 signs your well is running dry
1. Water sputters, then comes back
This is the most telling sign. The pump draws the water down below its intake during a long shower or a load of laundry, sucks air, and the flow stops.
After an hour or two, water seeps back in and everything seems normal again. That pattern means demand is outrunning what the well can supply.
2. Air spitting from the taps
When the water level drops near the pump, air gets pulled into the line. Our guide to air in well water lines covers the other causes, such as a leak in the drop pipe.
3. Muddy, cloudy or sandy water
As the level falls, the pump pulls from the bottom of the well where silt and sand settle. Sudden cloudy water, brown water or sand in the water after heavy use is a warning sign.
4. The pump runs longer
A pump that used to fill the pressure tank in a minute or two and now runs for much longer is working against a lower water level or a weaker inflow.
5. Lower pressure during heavy use
Pressure that sags when two taps run at once, but is fine first thing in the morning, points to a well that recovers slowly. Constant low pressure has other causes, covered in low water pressure from a well.
6. Filters clog faster
If your sediment cartridge used to last months and now clogs in weeks, more silt is reaching the pump. The right sediment filter buys time while you fix the cause.
7. A change in taste or stains
Water drawn from a lower level can carry more iron and manganese, leaving a metallic taste and orange, brown or black stains, as Massachusetts drought guidance for well owners notes.
8. Drought, or neighbors with the same problem
A long dry spell lowers the water table across an area. If neighbors on wells report trouble too, the cause is more likely the aquifer than your equipment.
Problems that look like a dry well
Before you call a driller, rule out these common lookalikes. They are often far cheaper to fix.
| What you see | Dry well? | More likely cause |
|---|---|---|
| Pump clicks on and off every few seconds | Unlikely | Waterlogged pressure tank. See signs of a bad pressure tank |
| No water at all, even after a long rest | Possible but rare | Pump, wiring or control box. See well pump not working |
| Breaker trips when the pump starts | Unlikely | Failing pump motor or capacitor. See pump keeps tripping the breaker |
| Pump will not shut off | Sometimes | Pressure switch or a pipe leak, or a well too low to reach cut off. See well pump will not shut off |
| Low pressure all day | Unlikely | Switch settings, clogged filter or plumbing. See pressure switch settings |
How to confirm your well is running low
- Measure the water level. A well sounder (water level meter) is a long tape with a probe that beeps when it touches water. Measure first thing in the morning and again after heavy use.
- Compare with the well log. Your well completion report lists the static water level and pump depth. Our guide on how deep your well is explains where to find it.
- Run a simple flow test. Time how long it takes to fill a bucket over a long run, as shown in how to test well flow rate.
- Watch the recovery. Measure the level again an hour after the pump stops. Slow recovery means a low yield well.
Our roundup of the best water level meters compares tape lengths and probe types.
What to do right now
- Cut demand. Stop lawn watering, car washing and long showers. Run the dishwasher and washer only when full, and space them out.
- Rest the well. Give it a few hours without heavy use so the level can recover.
- Protect the pump. A pump running dry overheats and can fail. A dry run protector or pump saver cuts power when the load drops, then restarts after a delay. See well pump protection devices.
- Keep drinking water on hand. Store some bottled water in case the supply runs out.
- Do not pour hauled water into the well. Much of it leaks away and it can bring in contamination, as the Massachusetts guidance warns.
Long term fixes for a well running dry
| Fix | When it helps | Good to know |
|---|---|---|
| Add a storage tank | Low yield wells that recover slowly | The well fills a tank slowly all day and a booster pump supplies the house |
| Lower the pump | There is unused depth below the pump | Can pull more sediment, so add a filter |
| Fit a smaller pump or flow restrictor | Pump draws water faster than the well recovers | Matches the pump to the yield |
| Hydrofracturing | Bedrock wells with poor fracture flow | Often helps in normal years, less certain in a drought |
| Deepen the well | Bedrock wells with room to go deeper | Adds storage; new water fractures are not guaranteed |
| Drill a new well | Dug or shallow wells, or a failing old well | Often better than deepening a shallow well |
Storage tanks: the quiet fix for low yield wells
Many low yield wells give plenty of water over a full day, just not fast enough for a shower and the washer at once. One homeowner with a well yielding about a quarter gallon a minute describes running a whole family from it with a large tank, a float switch and a booster pump (Plamondon: living with a low yield well).
Our guide to water storage tanks for well systems and the best float switches cover the parts.
See well storage tanks on Amazon
Deepening or replacing the well
Talk to a licensed well driller about the geology under your home. Shallow dug wells are often better replaced, while drilled bedrock wells can sometimes be deepened.
For costs, see well drilling cost and well pump replacement cost. Low income homeowners may qualify for USDA rural repair grants or loans.
How to protect your well before it runs low
- Fit low flow showerheads and fix running toilets, often the biggest household water waste.
- Water gardens early in the morning, by hand or with a drip line on a timer.
- Install a pump protector so a dry spell does not cost you a pump.
- Check the water level each season so you see a drop early.
- Test the water after a drought, since a lower water level can change its quality. See how often to test well water.
Planning for outages too? Read well water without power and battery backup for a well pump.
Frequently asked questions
What are the signs your well is running dry?
Water that sputters or stops during heavy use and returns after a rest, air in the taps, muddy or sandy water, a pump that runs longer than usual and lower pressure when several taps run at once.
Can a dry well come back?
Often, yes. If the cause is a drought or seasonal drop, the level usually recovers after rain refills the aquifer, though it can take weeks or months. A well that was always low yield needs storage or a pump change instead.
How long does it take a well to refill?
It depends on the yield. A strong well recovers in minutes, while a low yield well may take hours to refill after heavy use. Measuring the level an hour after the pump stops tells you your recovery rate.
Will running a well dry damage the pump?
Yes, it can. Submersible pumps rely on water for cooling, and running dry can overheat the motor. A dry run protector cuts power before damage is done.
Should I deepen my well or drill a new one?
It depends on the type of well and the rock below. Drilled bedrock wells can sometimes be deepened, while shallow dug or sand and gravel wells are often better replaced. A local driller can advise.






