Jet Pump vs Submersible Pump: Which Well Pump Do You Need?

Boreholeflow is reader supported. When you buy through links on this page, I may earn a commission at no extra cost to you. Read the full disclosure.

Quick answer
  • A jet pump sits above ground and pulls water up by suction. A shallow jet works to about 25 feet; a deep well (convertible) jet reaches roughly 90 feet with an ejector in the well.
  • A submersible pump hangs inside the well and pushes water up. It is the standard choice for deep wells and runs silently.
  • Jet pumps cost less and are easy to service, but they are noisy, need priming and use more power per gallon.
  • Submersibles cost more to install and pull, but they need no priming, are more efficient and do not freeze in a pump house.

Every well pump does the same job, getting water from the well to your pressure tank. The difference is where the pump sits and how it moves the water, and that decides your depth limit, noise, power bill and repair costs.

This guide compares jet pumps and submersibles side by side, explains when each one makes sense and gives you a picker that matches a pump type to your well. I link to my own buying guides for each type, and to installed cost figures from published cost guides.

Jet pump or submersible? Well pump picker

Jet pump or submersible? Well pump picker

Enter your pumping water level and casing size. We show which pump type fits and why.

Not sure of your water level? See how deep is my well and use a well sounder to measure it while the pump runs.

Jet pump vs submersible pump: side by side

Jet pumpSubmersible pump
Where it sitsAbove ground: basement, garage or pump houseDown in the well, below the water
How it moves waterPulls by suction, helped by a jetPushes water up the drop pipe
DepthShallow jet to about 25 ft; deep jet to about 90 ftShallow to several hundred feet
Casing sizeAny; only pipes go in the wellUsually 4 inch or larger (3 inch models exist)
PrimingNeeded, and it can lose primeNot needed
NoiseAudible where it is installedSilent at the house
EfficiencyLower: some water recirculates through the jetHigher for the same flow
Installed cost$400 to $1,000 shallow; $500 to $1,400 deep$1,000 to $2,500
ServiceEasy to reach and swapMust be pulled from the well

Installed cost ranges from HomeGuide, via my well pump replacement cost guide, accessed November 2026.

How a jet pump works

A jet pump spins an impeller that pushes water to the house. Some of that water is sent back through a nozzle and venturi, the jet, which creates low pressure that helps draw more water up the suction pipe.

On a shallow well pump the jet is built into the pump body and only one suction line goes into the well. On a deep well or convertible pump, the jet (ejector) sits down in the well on two pipes, or one pipe with a packer, so the pump can lift from deeper water.

Suction has a hard limit. Air pressure can only push water up about 34 feet in theory, and pipe friction and the foot valve cut that to about 25 feet in practice. My best shallow well jet pumps guide explains the math.

See shallow well jet pumps on Amazon

How a submersible pump works

A submersible is a long, narrow pump and motor sealed in one unit. It hangs on the drop pipe below the water level and pushes water up to the pressure tank, so there is no suction limit.

Submersibles come as 2 wire models, with the start parts inside the motor, or 3 wire models with a control box at the house. See 2 wire vs 3 wire well pumps to tell which you have, and the best submersible pumps for picks.

See submersible well pumps on Amazon

Depth is the deciding factor

The number that matters is the pumping water level: how far the water sits below the pump while it runs, not how deep the well was drilled. A deep well with water standing near the top can still suit a jet pump.

Pumping water levelBest pump typeNotes
Up to about 25 ftShallow well jet or submersibleJet pump is cheapest; subtract about 1 ft of lift per 1,000 ft of elevation
25 to about 90 ftDeep well (convertible) jet or submersibleSubmersible is more efficient; deep jet suits 2 inch wells
Over about 90 ftSubmersibleJet pumps cannot lift efficiently this deep
Very deep or low yieldSubmersible with pump protectionSee pump protection devices

Need a size as well as a type? My well pump size guide works out flow and horsepower from your household and depth.

Cost to buy and run

A jet pump is cheaper upfront because it sits above ground and swaps out in a few hours. A submersible costs more to install, because the crew lowers pipe and wire down the well and deep pumps often need a hoist.

Running costs go the other way. A jet pump sends part of its water back through the jet, so it uses more electricity for the same gallons. My well pump electricity cost calculator shows what your pump costs to run each month.

Noise, priming and freezing

  • Noise. A jet pump hums and clicks where it is installed, so a basement pump can be heard upstairs. A submersible makes no noise you can hear at the house.
  • Priming. A jet pump must be full of water to work, and a leaking foot valve or suction fitting makes it lose prime. See how to prime a well pump. Submersibles never need priming.
  • Freezing. A jet pump in an unheated pump house can freeze and crack. A submersible sits in water below the frost line. See how to keep a well pump from freezing.

Lifespan and repairs

Most well pumps last about 10 to 15 years, and both types can reach that with a healthy pressure tank. Short cycling from a waterlogged tank is the biggest killer of either type; see well pump short cycling.

Repairs are easier on a jet pump because you can reach it. On a submersible, a failed pressure switch or control box is still a top side fix, but a dead motor means pulling the pump. Estimate remaining life with my well pump lifespan calculator.

Which should you choose?

Choose a jet pump ifChoose a submersible if
Your pumping water level is under 25 ft, or under 90 ft with a 2 inch casingYour water is deeper than about 25 ft and the casing is 4 inch or larger
You want to service the pump yourselfYou want a quiet house and lower power bills
Budget is the main concern todayYou live where winters freeze pump houses
You have a dug or driven point wellYou want steady pressure from a constant pressure system

Want even pressure at every tap? A constant pressure system pairs a submersible with a drive that changes the motor speed. Still have questions? Start with my well pump troubleshooting guide if your current pump is giving trouble.

Frequently asked questions

Is a jet pump or a submersible pump better?

A submersible is better for wells deeper than about 25 feet and for quiet, efficient running. A jet pump is better for shallow wells, 2 inch casings and owners who want to service the pump themselves.

How deep can a jet pump pull water?

A shallow well jet pump lifts water from about 25 feet at sea level. A deep well or convertible jet pump with an ejector in the well reaches roughly 90 feet.

Can I replace a jet pump with a submersible?

Yes, if the casing is large enough, usually 4 inch. You will need a new drop pipe, pump wire and possibly a control box, and the old jet pump and suction lines come out.

Does a submersible pump need priming?

No. A submersible sits below the water level, so it is always full of water. Only jet pumps and other above ground pumps need priming.

Which uses more electricity, a jet pump or a submersible?

A jet pump usually uses more power for the same flow, because part of the water it moves is sent back through the jet to keep it working.

Why is my jet pump losing prime?

The usual causes are a leaking foot valve, an air leak in a suction fitting or water dropping below the end of the suction pipe. See our guide on air in well water lines.

Similar Posts

Leave a Reply

Your email address will not be published. Required fields are marked *