Best Water Pressure Booster Pumps for Well Water (2026 Guide)
Boreholeflow is reader supported. When you buy through links on this page, I may earn a commission at no extra cost to you. Read the full disclosure.
- A water pressure booster pump raises pressure after your pressure tank or storage tank. It helps with weak upstairs showers, long pipe runs and pressure lost through filters.
- On a well, try the cheap fixes first: raise the pressure switch, check the tank air charge and change clogged filters.
- If the well itself runs low, a booster makes it worse unless you add a storage tank first.
- For most homes the best type is a constant pressure (variable speed) booster with dry run protection.
Low water pressure is one of the most common complaints I hear from well owners. Before anyone sells you a booster pump, it pays to know where the pressure is going.
This guide explains when a booster pump on a well helps and when it does not, the types to choose from and what to look for. The checker tells you if a booster is the right fix for your house.
Do you need a booster pump? Pressure checker
Do you need a booster pump? Pressure checker
Answer five questions about your well system. We tell you whether a booster pump will help, or whether a cheaper fix comes first.
How a booster pump works on a well
Your well pump pushes water into the pressure tank, and the pressure switch keeps it between two settings, often 30 and 50 psi. A booster pump sits after that tank and pushes water on to the house at a higher, steadier pressure.
Modern constant pressure boosters use a pressure sensor and a variable speed drive. Grundfos explains that the control compares the measured pressure with your set point and speeds the pump up or down to hold it.
A booster cannot create water. It only moves what the well, tank or storage cistern can supply, which is why yield matters.
Fixes to try before buying a booster
| Cause of low pressure | Cheap fix | Guide |
|---|---|---|
| Switch set at 20/40 or 30/50 | Raise to 40/60 if the pump can reach it | Pressure switch settings |
| Wrong tank air charge | Set 2 psi below cut in with the tank empty | Drain and recharge |
| Clogged sediment filter | Change the cartridge | Change a filter |
| Failing pressure tank | Replace the tank | Bad tank signs |
| Worn pump | Repair or replace the pump | Pump going bad |
| Low yield well | Storage tank plus booster | Test flow rate |
Read low water pressure from a well for the full troubleshooting list.
Types of booster pumps for well systems
| Type | How it works | Best for |
|---|---|---|
| Constant pressure (variable speed) | Sensor and drive hold a set pressure | Whole house, steady showers |
| Jet pump with pressure tank | Fixed speed pump and switch | Low cost, storage tank systems |
| Inline booster with flow switch | Starts when a tap opens | One shower or one floor |
| Constant pressure well pump system | Replaces the well pump control | When the well pump also needs work |
If your well pump is old anyway, a full constant pressure well system can be better value than adding a booster. See best constant pressure well pump systems.
Best water pressure booster pumps for well water
1. Grundfos SCALA2: best overall
The SCALA2 is an all in one booster with the pump, motor, sensor, drive and a small tank in one quiet unit. It holds a steady pressure as taps open and close, which is exactly what most homes want.
- Built in pressure sensor and variable speed control
- Compact and designed for indoor use
- Protection against running dry
2. Davey constant pressure boosters: best with a storage tank
Davey has built pressure pumps for tank and cistern systems for decades. Its constant pressure models suit homes where the well fills a storage tank and a booster feeds the house.
Check Davey boosters on Amazon
3. Jet pump booster with pressure tank: best value
A shallow well jet pump with a small pressure tank is the budget route. It is louder and pressure swings between the switch settings, but parts are cheap and easy to find.
See jet pump boosters on Amazon
4. Inline booster with flow switch: best for one shower
Small inline boosters start when a tap opens and suit a single weak shower or a top floor. They are not built for whole house flow.
Picks are based on published specifications and how each type suits well systems. Check flow and pressure ratings against your house before you buy.
How to size a booster pump
- Find your peak flow. Add up the fixtures that run at once. A shower uses about 2 to 2.5 gallons a minute, a kitchen tap about 1.5 to 2.
- Choose your target pressure. Most homes are happy at 50 to 60 psi at the tap.
- Allow for height. Each foot of rise costs about 0.43 psi.
- Match the supply. The booster must not draw more than your well or tank can give. See what size well pump do I need.
Installation basics
- Install after the pressure tank and any filters, so filters see lower pressure.
- Add isolation valves and a bypass so water still flows if the booster fails.
- Use dry run protection, especially on wells and storage tanks.
- Put it on its own circuit and protect it from freezing. See keep your well pump from freezing.
- Check local code. Many areas want a licensed plumber or electrician.
Frequently asked questions
Can I put a booster pump on a well?
Yes, after the pressure tank or a storage tank. It will not help if the well itself cannot supply enough water, so check yield first.
Will a booster pump increase water pressure from a well?
Yes, if the well and pump supply enough water but pressure is low at the taps. If the cause is a low switch setting, a waterlogged tank or a clogged filter, fix those first.
Where do you install a booster pump on a well system?
After the pressure tank and any water treatment, before the house plumbing. With a storage tank, the booster draws from the tank and feeds the house.
What is better, a booster pump or a constant pressure well pump?
If your well pump is healthy, a booster is simpler. If the pump is old or you are replacing it anyway, a constant pressure well pump system solves pressure at the source.
How much pressure should a well system have?
Most homes run 40/60 psi or 30/50 psi at the pressure switch. With a booster you can hold a steady 50 to 60 psi at the taps.
Does a booster pump use a lot of electricity?
Variable speed boosters only run as fast as needed, so they use less power than fixed speed pumps. Running cost depends on how much water you use.






