How to Drain a Well Pressure Tank (and Reset the Air Charge)
Boreholeflow is reader supported. When you buy through links on this page, I may earn a commission at no extra cost to you. Read the full disclosure.
- Turn off the power to the pump at the breaker first.
- Open the tap or hose bib closest to the tank, usually on the tank tee, and let it run until the gauge reads 0 psi.
- With the tank empty, check the air charge on top with a tire gauge. Set it 2 psi below your cut in pressure, so 28 psi for a 30/50 switch.
- Close the tap, restore power and check for leaks as the pump refills the tank.
You drain a well pressure tank more often than you might think. You need it empty to check the air charge, replace a pressure switch, swap the tank or close up a cabin for winter.
The job takes about 10 to 20 minutes and needs nothing more than a garden hose and a tire gauge. This guide covers bladder tanks and old galvanized tanks, with a helper that gives you the right air pressure and steps for your setup.
Pressure tank drain and recharge helper
Pressure tank drain and recharge helper
Pick your switch setting, tank type and reason for draining. We give the air pressure to set and the steps that matter for your job.
When you need to drain a pressure tank
- Checking the air charge. You can only read the true pre charge when the tank holds no water.
- Replacing the pressure switch, gauge or a fitting. The system must be at zero pressure before you open anything.
- Replacing or moving the tank. An empty tank is far lighter and safer to handle.
- Winterizing. A cabin or empty house needs the tank and pipes drained before a freeze.
- A waterlogged tank. If the pump clicks on and off fast, the tank has lost its air cushion.
Short cycling is the most common reason. My well pump short cycling guide explains why a waterlogged tank wears out pumps.
What you need
- A garden hose long enough to reach a drain or outside
- A tire pressure gauge (a digital one reads low pressures more clearly)
- A bike pump or small air compressor to add air
- A bucket and rag for the last of the water
- Thread seal tape if you will open any fittings
See tire pressure gauges on Amazon
How to drain a bladder pressure tank, step by step
- Turn off the pump. Switch off the breaker marked for the well pump. If it is not labelled, switch off the one feeding the pressure switch and confirm the pump will not start.
- Find the drain point. Most tanks sit on a tank tee with a hose bib or drain valve. If yours has none, use the nearest tap.
- Attach a hose and open the valve. Run the hose to a floor drain or outside, away from the well head.
- Run it to zero. Watch the gauge fall to 0 psi. The air in a bladder tank pushes most of the water out for you.
- Open a tap upstairs. This lets air into the pipes so the last water drains from the tank tee.
- Do your job. Check the air charge, change the switch or remove the tank.
- Close everything and restart. Close the drain, turn the breaker on and watch the pump fill the tank to its cut out pressure.
A bladder or diaphragm tank never empties completely through the drain, and it does not need to. The bladder holds the air, and the small amount of water left does not affect the air reading.
Checking and setting the air charge
The air valve sits on top of the tank under a plastic cap and looks like a tire valve. With the tank at 0 psi water pressure, press your gauge on it and read the pre charge.
| Pressure switch setting | Set the air charge to |
|---|---|
| 20/40 psi | 18 psi |
| 30/50 psi | 28 psi |
| 40/60 psi | 38 psi |
| 50/70 psi | 48 psi |
Add air with a bike pump or compressor, or let some out by pressing the valve core. Read my pressure switch settings guide if you are not sure which setting you have.
If water spits out of the air valve, the bladder has split. No amount of air will fix that, so price a new tank in my pressure tank replacement cost guide.
Draining an old galvanized tank
Older galvanized tanks have no bladder, so air and water sit together and the air slowly dissolves into the water. When the air is gone the tank is waterlogged and the pump short cycles.
- Turn off the pump at the breaker.
- Open the drain at the bottom of the tank.
- Open a tap, plug or air inlet near the top so air can rush in as the water leaves.
- Let the tank empty completely.
- Close the drain and the top opening, then restore power. The tank refills with a fresh cushion of air.
Most galvanized tanks have an air volume control that should keep the air topped up. If yours waterlogs every few weeks, that part has failed; the Flotec air volume control kit is a common fix.
How long does it take to drain a pressure tank?
A typical 20 to 44 gallon bladder tank drains in about 5 to 10 minutes through a hose. Large galvanized tanks hold far more water and can take 20 minutes or longer.
Not sure your tank is the right size? Try my pressure tank sizing calculator while it is empty.
Problems you may find while the tank is empty
| What you see | What it means | What to do |
|---|---|---|
| Water from the air valve | Split bladder | Replace the tank |
| Air charge at 0 psi and will not hold air | Leaking air valve or tank | Replace the valve core, or the tank |
| Rust or weeping at the bottom seam | Tank corroding | Plan a replacement soon |
| Sand or grit in the drain water | Sediment from the well | See sand in well water |
| Clogged tube under the pressure switch | Sediment build up | Clean or replace the switch |
Need a new tank? My best well pressure tanks guide compares sizes and brands, and signs of a bad pressure tank covers the other warning signs.
See well pressure tanks on Amazon
Closing a cabin for winter? Follow my cabin well winterizing guide after the tank is empty, and see how to keep a well pump from freezing.
Frequently asked questions
How do I drain my well pressure tank?
Turn off the pump at the breaker, attach a hose to the drain valve on the tank tee and open it until the gauge reads zero. Open a tap in the house to let the last water drain.
Do I need to drain a pressure tank to check the air?
Yes. The air charge only reads correctly when the tank holds no water and the gauge reads 0 psi.
What should the air pressure be in my well tank?
Set it 2 psi below the cut in pressure of your switch: 28 psi for a 30/50 switch or 38 psi for a 40/60 switch.
How often should you drain a well pressure tank?
A bladder tank does not need regular draining, but check its air charge about once a year. Old galvanized tanks may need draining whenever they waterlog.
Why does water come out of the air valve on my pressure tank?
The bladder inside has split. The tank cannot hold an air cushion any more and should be replaced.
Can I drain a pressure tank without turning off the pump?
No. The pump will start as soon as pressure drops and keep refilling the tank. Always switch off the breaker first.






