Well Pump Making Noise? What Clicking, Humming and Banging Mean

Boreholeflow is reader supported. When you buy through links on this page, I may earn a commission at no extra cost to you. Read the full disclosure.

What to know
  • Rapid clicking at the pressure switch means the pump is short cycling, usually because the pressure tank is waterlogged.
  • A bang or thud when the pump stops is water hammer, most often from a worn or leaking check valve.
  • Humming with no water means the motor cannot start: on a 3 wire submersible, check the start capacitor in the control box.
  • Grinding or screeching from a jet pump points to worn bearings. Turn it off before it does more damage.

A healthy well system makes a few normal sounds: the click of the pressure switch, a soft hum while the pump runs and the hiss of water filling the tank. New or louder noises are often the first warning that something is wearing out.

This guide matches each sound to its likely cause, shows what to check first and tells you when to call a pump installer. Use the diagnoser for a quick answer.

Well pump noise diagnoser

Well pump noise diagnoser

Pick the sound you hear and when it happens. We show the most likely cause, how urgent it is and what to do first.

Normal well pump sounds

  • One click at the pressure switch when the pump starts, and another when it stops.
  • A steady hum from a jet pump while it runs. A submersible is deep in the well and usually silent at the house.
  • Water rushing into the pressure tank for a minute or two.
  • A run time of at least a minute. Anything shorter is short cycling.

Well pump noise chart

SoundMost likely causeHow urgent
Humming, but no waterThe motor has power but cannot start.Fix soon
Rapid clicking at the pressure switchThe pump is turning on and off every few seconds.Fix this week
Bang or thud when the pump stops or startsThis is water hammer.Fix this week
Grinding, screeching or squealingOn an above ground jet pump this usually means worn motor bearings or a rubbing impeller.Fix soon
Gurgling, sputtering or sucking airThe pump is drawing air.Fix this week
Running constantly, never shuts offThe pump cannot reach the cut out pressure.Fix soon
Buzzing or chattering at the switchWorn or pitted pressure switch contacts buzz and chatter as they open and close, and ants or debris between the contacts make it worse..Fix this week

Causes are the common ones, not the only ones. When in doubt, turn the pump off and check before it runs dry or overheats.

Clicking: the pump turns on and off fast

The pump is turning on and off every few seconds. This is short cycling, usually caused by a waterlogged pressure tank, a tank with the wrong air charge or a clogged pipe nipple under the switch.

  1. Turn off the pump breaker and open a tap until the pressure gauge reads zero.
  2. Check the air charge at the tank valve with a tire gauge. It should be 2 psi below the cut in pressure, such as 38 psi for a 40/60 switch.
  3. If water comes out of the air valve, the bladder has failed and the tank needs replacing.
  4. Remove and clear the small pipe nipple under the pressure switch if it is clogged with scale.

Our pressure tank sizing calculator checks whether your tank is big enough to give the pump a proper run time.

Check tire gauges on Amazon

Banging and water hammer

Water hammer is a pressure surge in the pipes. According to Grundfos, it often happens when the check valve sits too far above the water level or leaks, so a vacuum forms in the pipe and the water slams into it when the pump restarts.

  • Bang when the pump stops: a check valve snapping shut. A spring loaded check valve closes more gently.
  • Bang when the pump starts: often a leaking check valve that let the pipe drain.
  • Bang when a tap closes: fast closing valves on washing machines and dishwashers. A water hammer arrester fixes this.

Grundfos warns that repeated surges can burst pipes, break joints and damage the pump, so persistent hammering is a job for a pump installer.

See water hammer arresters on Amazon

Humming but no water

The motor has power but cannot start. On a 3 wire submersible the usual cause is a failed start capacitor or relay in the control box. On a jet pump it can be a seized impeller or a bad capacitor on the motor.

Turn the pump off at the breaker so the motor does not overheat. Then follow how to test a well pump capacitor or, if the breaker keeps tripping, why a well pump keeps tripping the breaker.

Grinding, screeching or squealing

On an above ground jet pump this usually means worn motor bearings or a rubbing impeller. On any pump it can mean sand or grit is passing through.

Worn bearings get louder quickly and can seize the motor. A pump that has run dry for long can also be damaged; see signs your well pump is going bad.

Gurgling, sputtering or sucking air

The pump is drawing air. On a jet pump that points to an air leak on the suction side. On any pump it can mean the water level is falling close to the pump intake.

Spitting taps and milky water are clues too. Read air in well water lines for the full checklist.

When to call a pump professional

  • The pump hums but will not start, even with a good capacitor.
  • You hear grinding, or smell burning near the motor.
  • Water hammer keeps getting worse or a fitting has started to leak.
  • The pump runs nonstop and you cannot find a leak in the house.
  • The noise comes with dirty water, sand or a big drop in pressure.

Pulling a submersible pump is heavy, specialist work. Our well pump replacement cost guide shows what to expect if it comes to that.

Frequently asked questions

Why is my well pump clicking on and off?

Rapid clicking means the pump is short cycling. The usual causes are a waterlogged pressure tank, the wrong tank air charge or a clogged pipe nipple under the pressure switch.

What causes banging pipes on a well system?

Banging is usually water hammer from a check valve that slams shut or leaks. Fast closing appliance valves can cause it too, and a water hammer arrester often helps.

Why is my well pump humming but not pumping?

The motor has power but cannot start. On a 3 wire submersible, the start capacitor or relay in the control box is the most common cause; a jet pump may also have lost its prime.

Is it normal to hear a submersible well pump?

Usually not at the house, because the pump is deep in the well. You will hear the pressure switch click and water filling the tank.

Can a noisy pressure tank be fixed?

Often yes. Setting the right air charge fixes many noisy, cycling systems, but a tank with a failed bladder needs replacing.

Similar Posts

Leave a Reply

Your email address will not be published. Required fields are marked *