How Much Does It Cost to Run a Well Pump? (Electricity Cost Calculator)

Boreholeflow is reader supported. When you buy through links on this page, I may earn a commission at no extra cost to you. Read the full disclosure.

Quick answer
  • A typical home well pump costs about $3 to $6 a month to run for a family of four.
  • That assumes 82 gallons per person a day (EPA), a 10 GPM pump and the 2026 US average electricity price of about 18 cents per kWh (EIA).
  • A 1/2 HP submersible draws about 960 watts and a 1 HP about 1,600 watts at maximum load (Franklin Electric).
  • If your bill suggests much more, look for short cycling, a pump that never shuts off, leaks or heavy irrigation.

A lot of well owners worry that the pump is the big number on their electric bill. In most homes it is not: the pump only runs while you use water, and that adds up to well under an hour a day.

I built the calculator below so you can put in your own pump size, household and power rate. Under it I explain where the numbers come from and what pushes the cost up.

Well pump electricity cost calculator

Well pump electricity cost calculator

Enter your pump, household and electricity rate. Your rate is on your power bill in cents per kWh.

Watts are Franklin Electric maximum load figures for 4 inch single phase submersibles, so the result leans high. Jet pumps and other brands differ; check your motor label.

How the math works

A pump only uses power while it runs. So the cost comes down to three things: how many gallons you use, how fast the pump moves them and how many watts it draws.

  1. Gallons a day. The EPA says each American uses about 82 gallons of water a day at home.
  2. Run time. Gallons divided by pump flow. 328 gallons at 10 GPM is about 33 minutes.
  3. Energy. Watts times hours. 960 watts for 0.55 hours is about 0.5 kWh a day, or 16 kWh a month.
  4. Cost. kWh times your rate. 16 kWh at 18.2 cents is about $2.90 a month.

The EIA put the average US residential price at 18.19 cents per kWh for January to August 2026, which is the default in the calculator. Your own rate may be much higher or lower.

Monthly cost by household and pump size

PeoplePumpGallons a dayRun time a dayEnergy a monthCost a month
21/2 HP16416 min8.0 kWh$1.45
21 HP16416 min13.3 kWh$2.42
41/2 HP32833 min16.0 kWh$2.90
41 HP32833 min26.6 kWh$4.84
61/2 HP49249 min23.9 kWh$4.36
61 HP49249 min39.9 kWh$7.26

Assumes a 10 GPM pump, 82 gallons per person a day and 18.2 cents per kWh. A bigger pump usually also moves more water per minute, which shortens run time, so real costs for 1 HP pumps are often lower than shown.

Well pump watts by horsepower

Pump sizeRunning watts (max load)Typical use
1/2 HP960 WShallow to medium wells, small homes
3/4 HP1,310 WAverage homes, medium depth
1 HP1,600 WDeeper wells or larger homes
1.5 HP2,280 WDeep wells, irrigation, big households

Figures for Franklin Electric 4 inch single phase submersible motors from the Franklin AIM manual, as compiled by Power Outage Planner. At full load rather than maximum load, a 1/2 HP 2 wire motor draws about 670 W.

Starting watts are much higher than running watts, but a start lasts under a second, so it barely shows on your bill. It matters a lot for a generator or battery backup.

Not sure what size you have? My well pump size guide shows how to read the label on the control box or pressure switch.

Measure your own pump

The most accurate way is to measure amps on one leg of the pump circuit while it runs. Multiply amps by volts for a rough watt figure; it reads a little high because it ignores power factor.

  • Turn on a tap so the pump runs steadily.
  • Clamp an AC clamp meter around one hot wire at the pressure switch or control box. Keep your hands clear of live terminals.
  • Time a full pump cycle with a stopwatch and count cycles over an evening to estimate daily run time.

If you are not comfortable working near live 240V wiring, ask an electrician or pump installer to take the reading.

Check clamp meters on Amazon

What makes a well pump cost more

  • Short cycling. A waterlogged pressure tank makes the pump start every few seconds, and each start draws a surge. See well pump short cycling.
  • A pump that never shuts off. A leak, a worn pump or a low well can keep it running for hours. See well pump won’t shut off.
  • Leaks and running toilets. The EPA says household leaks can waste about 180 gallons a week in a typical home.
  • Irrigation and animals. A lawn sprinkler can use more water in an hour than the house uses in a day. Add it in the extra gallons box.
  • Low flow. A pump that has worn down or a well that has dropped moves fewer gallons per minute, so it runs longer. My flow rate test shows how to check.

How to cut the cost

  1. Check the pressure tank air charge every year. Use the pressure tank sizing calculator to make sure the tank is big enough.
  2. Fix leaks and replace toilet flappers that let water trickle.
  3. Water the garden early and use drip lines instead of sprinklers.
  4. Consider a constant pressure system when your pump is due for replacement. Variable speed pumps slow down for small demands. See constant pressure well pump systems.

Weighing a new pump anyway? My well pump replacement cost guide covers what it costs to swap one.

Frequently asked questions

How much does it cost to run a well pump?

For a family of four using about 330 gallons a day, a 1/2 HP submersible pump costs roughly $3 a month at the 2026 US average electricity price of about 18 cents per kWh. Bigger pumps, irrigation and leaks raise that.

How many kWh does a well pump use per day?

A 1/2 HP pump drawing about 960 watts and running 30 to 35 minutes a day uses around 0.5 kWh. A 1 HP pump on the same run time uses about 0.9 kWh.

How many watts does a 1 HP well pump use?

Franklin Electric lists about 1,600 watts at maximum load for a 1 HP, 4 inch single phase submersible motor. Starting draws far more, which matters for generator sizing.

Why is my well pump using so much electricity?

The usual causes are a pump that short cycles, a pump that never shuts off, a leak or running toilet, and heavy irrigation. Each one adds run time, and run time is what you pay for.

Does a constant pressure pump use more electricity?

Not usually. A variable speed constant pressure pump slows down for small demands, so it can use less energy per gallon than a fixed speed pump.

How long should a well pump run each day?

For a typical household, total run time is often under an hour a day. Each cycle should last at least a minute; shorter cycles mean the pressure tank needs attention.

Sources

Similar Posts

Leave a Reply

Your email address will not be published. Required fields are marked *