How to Change a Whole House Water Filter (Step by Step)

Boreholeflow is reader supported. When you buy through links on this page, I may earn a commission at no extra cost to you. Read the full disclosure.

What to know
  • Turn off the water supply, press the pressure release button, unscrew the housing with a filter wrench and swap the old cartridge for a new one.
  • Clean the housing and coat the O ring with food grade silicone grease before you screw it back on hand tight.
  • Turn the water back on slowly and check for leaks, then run a tap for a few minutes to flush the new cartridge.
  • Most sediment cartridges need changing every 3 to 6 months on well water; carbon cartridges often last 6 to 12 months.

A clogged whole house filter shows up as falling water pressure, rusty or cloudy water and a cartridge that has turned brown. Changing it takes about 15 minutes and needs no plumber.

This guide covers the tools, the step by step swap, how often to change each type of cartridge and how to fix the leaks that sometimes follow. Use the schedule maker to set your next change date.

When should I change my filter? Schedule maker

When should I change my filter? Schedule maker

Tell us about your filter and water. We suggest how often to change the cartridge and the date for your next change.

Cartridge typeTypical change on well waterChange sooner if
Sediment, pleated or string woundEvery 3 to 6 monthsPressure drops or the cartridge is dark with grit
Carbon blockEvery 6 to 12 monthsTaste or odor returns
Iron or manganese reductionEvery 3 to 6 monthsOrange or black staining returns
Spin down sediment screenRinse monthly; screen lasts yearsThe screen tears or will not flush clean

Typical ranges for well water. Your water and the cartridge maker’s rating decide the real interval.

Signs it is time to change the filter

  • Lower water pressure at every tap, especially the shower.
  • Dirty, rusty or cloudy water getting through.
  • Taste or smell coming back with a carbon filter.
  • The cartridge is dark when you look through a clear housing.
  • A pressure drop across the filter of 10 psi or more if you have gauges before and after it.

Sudden cloudiness or grit can also be a well problem. See cloudy well water and sand in well water.

What you need

  • The right replacement cartridge. Check the size and micron rating printed on the old one.
  • A filter housing wrench, usually supplied with the housing.
  • Food grade silicone grease for the O ring.
  • A bucket and towels for the water in the housing.
  • Disposable gloves and a little unscented bleach if you sanitize the housing.

See housing wrenches on Amazon

How to change a whole house water filter

  1. Turn off the water. Close the valve before the filter, or set the bypass valve to bypass. On a well you can also switch off the pump breaker.
  2. Release the pressure. Press the red pressure release button on top of the housing, or open a tap downstream.
  3. Unscrew the housing. Put the bucket underneath and turn the housing counterclockwise with the wrench.
  4. Remove the old cartridge. Note which way it sat and dispose of it.
  5. Clean the housing. Rinse out the sediment. To sanitize, wash it with a weak bleach solution and rinse well.
  6. Check the O ring. Wipe it clean, look for cracks or flat spots, and coat it lightly with silicone grease. Seat it fully in its groove.
  7. Fit the new cartridge. Center it on the post in the housing so it sits straight.
  8. Screw the housing back on. Hand tight, then a quarter turn with the wrench at most.
  9. Turn the water on slowly. Press the release button to let trapped air out, then check for drips.
  10. Flush. Run a cold tap for a few minutes. Carbon cartridges may run grey at first.

If you lost prime or pressure on a jet pump while the water was off, see how to prime a well pump.

Whole house filter cartridge sizes

SizeWhere you see itNotes
10 x 2.5 inch (standard)Small under sink and point of entry housingsLow flow; clogs fastest on well water
20 x 2.5 inchSlim tall housingsTwice the media of a 10 inch
10 x 4.5 inch (Big Blue)Most whole house housingsHigher flow and longer life
20 x 4.5 inch (Big Blue)Large homes and heavy sedimentThe longest life between changes

Match the micron rating too. Many well systems use a coarser sediment cartridge first and a finer one or a carbon block after it. Compare systems in our best whole house filters for well water.

Shop replacement cartridges: Big Blue sediment cartridges, Big Blue carbon blocks and standard 10 inch cartridges.

Fixing leaks after a filter change

  • Drip at the top seam: the O ring is twisted, dry or out of its groove. Turn the water off, reseat it and add grease.
  • Still leaking: the O ring is worn or cracked. Replacement O rings are cheap; buy the one for your housing model.
  • Leak at the threads: the housing is cross threaded or overtightened. Unscrew and start again by hand.
  • Crack in the housing: replace the housing. Do not run a cracked housing under pressure.

Make your cartridges last longer

  • Add a spin down prefilter that catches sand before it reaches the cartridge. See best sediment filters for well water.
  • Treat iron at the source. Heavy iron clogs cartridges fast; an iron filter is better. See how to remove iron from well water.
  • Fit pressure gauges before and after the housing so you can see when the filter is clogging.
  • Write the date on the housing with a marker each time you change it.

Frequently asked questions

How often should I change my whole house water filter?

On well water, most sediment cartridges need changing every 3 to 6 months and carbon cartridges every 6 to 12 months. Change sooner if pressure drops or the water quality slips.

Do I need to turn off the water to change a whole house filter?

Yes. Close the valve before the filter or use the bypass, then press the pressure release button before you unscrew the housing.

Why is my filter housing leaking after I changed the cartridge?

The O ring is usually twisted, dry or out of its groove. Turn the water off, reseat the O ring with food grade silicone grease and tighten the housing by hand.

Why is my water pressure low after changing the filter?

Trapped air or a too fine cartridge can lower pressure. Bleed the air with the release button; if pressure stays low, check that the micron rating matches your old cartridge.

Can I clean and reuse a sediment filter cartridge?

Most pleated and string wound cartridges are made to be replaced, not cleaned. Spin down screens are the exception and are designed to be rinsed.

Similar Posts

Leave a Reply

Your email address will not be published. Required fields are marked *